100-200 kg/h Wood Stove Pellet Making Machine
| Voltage: | Customized | Function: | Pellet Processing Machine |
| Pelletdiameterrange: | 6-12 Mm | Motorpower: | 15-110 KW |
| Color: | As Customer Requirements | Application: | Fuel Pellets For Heating, Animal Bedding, Biomass Energy |
| Materialprocessed: | Wood Sawdust, Wood Chips, Straw, Agricultural Waste | Spare Parts: | Flat Die+ Rollers |
| Powersource: | Electric Motor | ||
| High Light: | wood stove pellet making machine,100-200 kg/h pellet machine,wood pellets machine |
||
A 100-200 kg/h wood stove pellet making machine is a flat die press with a 15 kW main motor, a 4-6 mm die and a 0.5 t frame. It presses dry sawdust into 6 mm pellets without a binder, because the lignin in the wood softens under pressure in the die and bonds the pellet as it cools. It runs on 400 V three phase at 50 Hz and measures 1400 x 600 x 1000 mm. Manufacture takes 20-25 days, it ships as one 0.5 t case, and the frame, motor and drive carry a twelve month warranty.
- What Is Included in a 100-200 kg/h Wood Pellet Machine?
- Which Raw Materials Can a Wood Pellet Machine Press?
- Can a Wood Stove Pellet Machine Run Without a Binder?
- What Output Does a 100-200 kg/h Wood Chip Pellet Machine Give?
- What Moisture Suits a Wood Stove Pellet Making Machine?
- Does a Wood Pellet Machine Need a Hardwood Die?
- Is a 6 mm Die Included With the Pellet Machine?
- What Are the Key Features of the Flat Die Pellet Machine?
- Will a Wood Pellet Machine Run on 400 V?
- What Spare Parts Does a Wood Fuel Pellet Making Machine Need?
- How Much Sawdust Does a Wood Pellet Machine Need?
- What Service Comes With a Wood Stove Pellet Machine?
- How Is a Wood Fuel Pellet Making Machine Shipped to Europe?
- What Does a Flat Die Wood Pellet Machine Quote Cover?
A flat die wood pelletizer mill is the simplest press geometry there is: rollers above a plate, and material forced down through the plate. A flat die press compresses powder. Wood chips, shavings and offcuts have to be reduced to sawdust before they reach the hopper, and a press fed anything coarser will block at the die rather than form a pellet.
One press, one die, one roller set and a starter, delivered as a single working unit.
| Item | Specification |
|---|---|
| Press type | Flat die, horizontal plate, rollers above the plate |
| Main motor | 15 kW, 400 V, 50 Hz, three phase |
| Die supplied | 6 mm, interchangeable |
| Rollers | Two, running on the die face |
| Cutter | Adjustable, mounted on the die face |
| Frame | Welded steel, 0.5 t |
| Dimensions | 1400 x 600 x 1000 mm |
| Starting | Direct on line starter, supplied with the machine |
| Packing | Plywood case, die and rollers boxed inside |
Table 1: What ships with the press. The die and one roller set are included; a spare die is a separate line on the quotation.
Every item above is chosen for one job: pressing dry sawdust into 6 mm pellets at 100-200 kg/h. A larger motor would not raise the output, because the limit at this size is the die area rather than the drive.
Dry sawdust from hardwood, softwood or a mix, and nothing that has not been reduced to powder.
| Material | Form | Presses | What to Watch |
|---|---|---|---|
| Oak and beech sawdust | Dry powder, 10-15 percent | Yes | Rate drops to the lower end, die wears faster |
| Spruce and pine sawdust | Dry powder, 10-15 percent | Yes | Highest rate, easiest material in the range |
| Mixed hardwood and softwood | Dry powder | Yes | Rate tracks the hardwood share |
| MDF and board dust | Fine dry powder | Yes | Resin is abrasive, die life shortens |
| Wood shavings | Curled strips | No | Must be ground to sawdust first |
| Wood chips | Chips from a chipper | No | Bridges above the die and stops the rollers |
| Green or wet sawdust | Above 15 percent | No | Steam splits the pellet and the die blocks |
| Straw and grass | Chopped fibre | Not reliably | Lower lignin, usually needs a binder |
Table 2: What the press takes and what it refuses. The refusal rows are the ones that save a buyer a wasted season.
The form of the material is the single condition that decides whether the press works. Sawdust pressed at 12 percent bonds on its own lignin; the same wood arriving as chips has to go through a hammer mill first, and a farm that buys the press without a mill usually ends up buying the mill within a month.
Yes. Wood bonds to itself under pressure, and no additive is needed for oak, beech, spruce or a mix of all three.
The bonding agent is lignin, the natural polymer that holds wood fibres together. Inside the die the material sees high pressure and the friction of being forced through a hole, the lignin softens, and on the way out the pellet cools and the lignin sets. That is why a wood pellet holds its shape with nothing added.
A wood pellet machine without binder still needs the moisture in the band and the die in good condition, because those are what stand in for the additive.
| Material | Binder Needed | Why |
|---|---|---|
| Hardwood sawdust, oak and beech | No | Lignin content is high, pellets bond readily |
| Softwood sawdust, spruce and pine | No | Lignin content is high, pressing is slightly easier |
| Mixed hardwood and softwood | No | The mix behaves like the average of the two |
| Wood chips and shavings | No, but must be ground first | The press compresses powder, not chips |
| Straw and grass | Often yes | Lignin content is lower and the fibre is waxy |
Table 3: What needs a binder and what does not. The distinction in the wood rows is about particle size, not about chemistry.
A press fed chips will not make a weaker pellet, it will stop.
The flat die biofuel sawdust pellet machine is built for exactly that material, and it will not press chips. Chips bridge above the die and the rollers cannot draw them in, so the material sits in the chamber and the motor load climbs. Grinding to sawdust first is not an optional refinement on a flat die press, it is the condition for running at all.
Between 100 and 200 kg/h depending on the species, and a hardwood mix sits at the lower end of that band.
| Feedstock | Output |
|---|---|
| Spruce and pine sawdust | 160-200 kg/h |
| Mixed spruce and beech | 130-170 kg/h |
| Oak and beech sawdust | 100-140 kg/h |
Table 4: Output by species on the same press and the same 6 mm die. Dense hardwood takes more pressure per kilogram, so the hourly rate falls.
The rate also follows the die. A 6 mm die passes more material per hour than a 4 mm die at the same pressure, because each hole is larger and the press does less work per kilogram. A machine quoted at 200 kg/h on 6 mm will give less on 4 mm, and that is a die effect rather than a motor limit.
A flat die pellet mill 6 mm die presses about 100 kg/h on oak and about 200 kg/h on spruce, which is the band quoted for this machine.
One tonne of pellets a year is about five to ten hours of running on this press.
A small wood pellet machine for home use is bought on that basis rather than on the hourly rate, because the machine spends most of the year idle. That is worth stating plainly, because it changes how the machine is bought. A press bought for a tonne a year is bought for the die and the build quality, not for the hourly rate, and a smaller machine would not be cheaper to own once the die and the frame are counted.
12 percent, and the band that works runs from about 10 to 15 percent.
| Moisture | What Happens in the Press |
|---|---|
| Below 10 percent | Pellets form but stay brittle, and the die runs hot |
| 10-15 percent | Best band, pellet is dense and holds its shape |
| Above 15 percent | Steam flashes at the die, the pellet splits and the press load jumps |
| Above 20 percent | The press blocks and the die has to be cleared |
Table 5: Moisture against press behaviour. The 12 percent figure is the middle of the working band, not an exact requirement.
Sawdust stored under cover in a dry climate settles near 10-12 percent on its own. Sawdust from a sawmill that cuts green timber arrives at 30 percent or more, and that material has to be dried before it goes anywhere near the press.
A moisture meter is the one instrument worth buying with the machine. The difference between 12 and 18 percent is not visible by hand, and it is the difference between a bag of pellets and a blocked die.
No. One die presses hardwood and softwood, and a 6 mm die is supplied with the machine.
Hardwood is denser than softwood, so it draws more power per tonne and it wears the die faster, but it does not need a different die geometry.
A pellet mill for oak beech spruce sawdust is bought with one die for all three, and the rate moves with the species rather than the die. What changes is the rate, as the output table shows, and the interval between die changes.
| Species Group | Die Needed | Wear Rate |
|---|---|---|
| Spruce, pine, fir | Standard die | Normal |
| Oak, beech, ash | Standard die | Faster, denser and more abrasive |
| Tropical hardwood | Standard die | Fastest, and the rate drops most |
Table 6: Die choice by species. The die geometry does not change; the life of the die does.
A die wears from the inlet side, where the taper leads the material into the hole. Once the taper polishes smooth the material stops being guided in and the press starts to slip, which shows up as a lower output at the same motor load. That is the point to change the die, not the point where it cracks.
Yes. The 6 mm die is the standard fitment on this machine and it is the size most stove owners want.
A 6 mm pellet is the common European stove size, and it is the size most flat die presses in this class are set up for. A 4 mm die is available for smaller stoves and for buyers who want a finer pellet, and it is supplied as a separate die rather than as a substitute.
| Die Size | Typical Use |
|---|---|
| 4 mm | Small stoves, and buyers mixing pellets into other fuel |
| 6 mm | Domestic stoves and small boilers, the standard size |
| 8 mm | Larger stoves and small boilers |
Table 7: Die sizes for a flat die press in this class. The 6 mm die ships with the machine.
Pellet length is set by the cutter rather than the die.
A 100 kg/h wood pellet mill at the top of the band and a 200 kg/h run at the bottom use the same cutter setting, because length does not follow rate. The cutter sits on the outside of the die and is set to break the extruding rope at the length the buyer wants, usually two to three times the diameter.
Five features define this press: a horizontal die plate, rollers running on the die face, top access to the die, an adjustable cutter, and a fixed die with rotating rollers.
| Feature | What It Does | Why It Matters Here |
|---|---|---|
| Horizontal die plate | Material falls onto the plate by gravity | No feeder or distributor is needed at 100-200 kg/h |
| Rollers running on the die face | Press meal down through the holes | Even wear across the plate rather than one track |
| Top access to die and rollers | Die lifts out without dismantling the frame | A die change takes about 30 minutes by hand |
| Adjustable cutter on the die face | Sets pellet length as the rope extrudes | One die makes 12 mm and 18 mm long pellets |
| Fixed die, rotating rollers | One gearbox, one drive | Fewer parts to fail than a ring die at this size |
| Sealed roller bearings | Grease stays in, dust stays out | A press run once a week is not ruined by sitting |
Table 8: The flat die features that matter on a small press. The horizontal plate is what removes the need for a feeding system.
The horizontal plate is the reason a press this small works without a feeder. On a ring die the material has to be thrown outward against a vertical ring and kept evenly distributed, which needs a screw feeder and a distributor. On a flat die the material simply falls onto the plate and the rollers sweep it into the holes.
Yes. The 15 kW motor is a three phase motor and 400 V at 50 Hz is its standard supply.
| Supply Item | Requirement |
|---|---|
| Voltage | 400 V three phase |
| Frequency | 50 Hz |
| Main motor | 15 kW |
| Control | Direct on line starter, supplied with the machine |
| Cable | Sized to the 15 kW motor and the run length |
Table 9: Electrical requirement for the press. A 15 kW motor is not available as a single phase machine.
A 15 kW motor draws roughly 30 A per phase at 400 V, and the cable and the breaker are sized on that rather than on the motor nameplate alone.
A wood pellet machine 15 kw motor at 400 V is the standard build, and a 50 Hz supply is what the die and the cutter are timed around. A long run from the meter to the shed is the usual reason a press trips on start in a farm building, and it is a cable problem rather than a machine problem.
Denmark runs 230 V single phase and 400 V three phase at 50 Hz, so the press matches the supply without a transformer. The machine is also built to the machinery directive for sale into the European Union, and the CE documentation travels with it.
One spare die of the size in use and one set of rollers, and both are consumables rather than repairs.
| Part | Spare to Keep | Wear Sign |
|---|---|---|
| Die, 6 mm | One | Output falls at the same motor load |
| Rollers | One set | Roll surface tracks the die and flattens |
| Cutter blade | One | Pellet length drifts |
| Drive belt | One | Slipping under load |
Table 10: Spares for a flat die press. Die and rollers are replaced as a set because a new die against worn rollers wears on one side.
A die and a roller set are a matched pair in practice.
Wood pellet processing machine owners who keep one spare die of the size in production avoid the one failure that stops a press for weeks. Fitting a new die against rollers that have already worn to the old die leaves the new die running on a surface that no longer matches it, and the die wears unevenly from the first hour.
About 1.05 to 1.15 tonnes of sawdust at 12 percent moisture, and the difference is the fines that come back.
| Input | Output | Note |
|---|---|---|
| 1.1 t sawdust at 12 percent | 1.0 t pellets | Normal yield |
| 1.2 t sawdust at 15 percent | 1.0 t pellets | More water to flash off, more fines |
| 1.0 t sawdust at 10 percent | 0.95 t pellets | Dry feed makes brittle pellets and more dust |
Table 11: Input against output. The gap is fines and water, and fines are re-pressed rather than lost.
For a tonne a year the sawdust requirement is trivial, which is why the storage question matters more than the volume question. Sawdust stored in the open picks up moisture from the air, and a bag of sawdust that has been sitting under a lean-to since spring will not press at 12 percent.
A twelve month warranty, a priced spares list, remote support, and a production video with the CE documents.
| Item | What Is Covered |
|---|---|
| Warranty period | 12 months from commissioning |
| Warranty scope | Frame, motor, gearbox and starter |
| Wear parts excluded | Dies, rollers, cutter blades, drive belts |
| Spare parts supply | Priced list with the quotation, held for ten years |
| Die and roller supply | Any diameter in the 4-8 mm range, supplied as separate items |
| Technical support | Remote diagnosis by video call, plus a running video on wood sawdust |
| Documentation | Operation manual and CE declaration |
| Lead time | 20-25 days manufacture, then freight to the destination |
| Packing | One plywood case, about 0.5 t |
Table 12: Warranty, spares and delivery for a single press. A spare die and roller set are worth ordering with the machine rather than after it.
The spares question matters more on a small press than on a line, because a farm with one machine has no second press to fall back on. A spare die and a roller set ordered with the machine cost less than a stopped season, and they are the two parts that decide whether the press runs at 12 percent or at 18 percent.
On a pallet or in a plywood case, about 0.5 t, with the die and the rollers boxed separately inside the case.
| Item | Packing |
|---|---|
| Press frame and motor | Crated, 1400 x 600 x 1000 mm machine footprint |
| Die and rollers | Boxed inside the crate |
| Cutter and guard | Boxed inside the crate |
| Manual and CE documents | With the crate |
Table 13: Packing for a single press. A machine at this size ships as one case rather than as loose parts.
Delivery to a European address is normally quoted to the door, with the duty and the VAT shown as separate lines because they are charged at the destination rather than at origin. A buyer comparing quotations for a wood pellet making machine price is usually comparing what is inside the door-to-door figure, and