logo

1-1.5 t/h Wood or MDF Pellet Production Line

Basic Properties
Place of Origin: CHINA
Brand Name: MIKIM
Certification: CE、ISO
Model Number: MKLH
Trading Properties
Minimum Order Quantity: 1 Set
Price: $3500.00 - 55000.00/ Set
Payment Terms: L/C,D/A,D/P,T/T
Supply Ability: 50 sets per month
Specifications
Machinetype: Pellet Mill Usage: Making Wood Pellets
Machinedimensions: 2000x1500x1800 Mm Function: Pellet Processing Machine
Compressionratio: 1:1.5 To 1:2 Operatingvoltage: 380V/50Hz
Condition: New Packing: Standard Export Packing
Raw Material: Waste Wood Branch,Sawdust, Wood Chips, Shavings, MDF Offcuts And Mixed Hardwood Logs
High Light:

Wood MDF pellet production line

,

1-1.5 t/h pellet line

,

Wood pellets machine

Product Description

A 1-1.5 t/h wood or MDF pellet production line is twelve units in one row: a drum chipper, a hammer crusher with cyclone, two screw conveyors, a four-bend air duct dryer, a buffer bin with feeder, a ring die press, two belt conveyors, a cooler screener and a bagger. Connected load is 230.85 kW. The line takes logs up to 18 cm, sawdust at up to 80 percent moisture and MDF offcuts, and delivers 1-1.5 tonnes of 4-12 mm pellets per hour.

Complete 1-1.5 t/h wood biomass pellet production line arranged in a single row from chipper to bagging machine
Wood chip pellet line showing drum chipper, hammer crusher and air duct dryer connected in sequence
What Does a 1-1.5 t/h Wood Pellet Production Line Include?

Twelve units across seven stages, laid out as one row from the log deck to the bagging head. A wood pellet machine line at this tonnage is quoted unit by unit rather than as a package, because the dryer, the furnace and the press are each sized on a different input.

Table 1: The twelve units of the line. The chipper, the crusher and the dryer carry the largest motors after the press.
No.PhotoUnitModelPowerDuty
1—Drum chipperDC-21663.5 kWLogs under 18 cm, 5 t/h
2Hammer mill for wood chips and rice husk with cyclone and dust bagsHammer crusher60 hammers, 180 x 60 x 8 mm45 + 7.5 kW1500-2500 kg/h, with cyclone and dust bags
3Automatic small portable powder screw conveyor 3 m long, 150 mm diameterScrew conveyor, 3 m150 mm diameter1.5 kWChipper to crusher
4Sawdust pipe dryer with four-bend air duct for reducing moisture to 15 percentAir duct dryer400, four bends7.5 kW1.2-1.5 t/h, 17 m duct, inlet 10-80 percent to 15 percent
5Automatic small portable powder screw conveyor 6 m long, 150 mm diameterScrew conveyor, 6 m150 mm diameter1.5 kWDryer to buffer bin
6Buffer bin with 2.2 kW feeder steadying the infeed to the ring die pellet pressBuffer bin with feeder2.2 kW feeder2.2 kWSteadies the press infeed
7Biofuel sawdust ring die pellet machine MKLH560 producing 4-12 mm wood pelletsRing die pellet pressMKLH56090 kW1-1.5 t/h, 4-12 mm
8Belt conveyor 5680 x 1060 x 840 mm moving pellets from press to coolerBelt conveyor5680 x 1060 x 840 mm2.2 kWPress to cooler
9Horizontal counter flow pellet cooler and screener 1630 x 1100 x 3000 mmCooler and screener1630 x 1100 x 3000 mm4.75 kW1-2 t/h, 6-15 min cooling
10Belt conveyor 5680 x 1060 x 840 mm moving cooled pellets to the bagging machineBelt conveyor5680 x 1060 x 840 mm2.2 kWCooler to bagger
11Automatic bag filling and packing machine for 15-50 kg wood pellet bagsBagging machine15-50 kg per bag3 kW240-360 bags/h, plus or minus 0.2 percent
12—Electrical control box——Line control and interlocking

The chipper is rated 5 t/h against a 1.5 t/h line, and that gap is deliberate. A drum chipper is rated on volume, and a cubic metre of hardwood chips weighs roughly twice what a cubic metre of softwood chips weighs, so a machine that looks oversized on paper is matched to the line on a dense species.

Which Raw Materials Suit a Sawdust Pellet Line?

Sawdust, wood chips, shavings, MDF offcuts and mixed hardwood logs, with the moisture and the particle size doing more to the line rate than the species does.

Table 2: Feedstock forms and what each one changes. The line is configured against the mix, not against a single species.
Raw MaterialIncoming FormWhat Changes
Sawdust from a sawmill10-25 percent moisture, already fineBypasses the chipper, still goes through the dryer
Wood chips and slabs20-50 percent moisture, 5-30 cmChipper then crusher
MDF offcuts and board wasteDry, dense, fine dust when crushedCrusher load rises, die wear rises
Mixed hardwood logs18 cm and under, variable densityChipper speed follows the densest species in the pile

A sawdust pellet line fed from a joinery can skip the chipper entirely, because the material is already the size the dryer wants. A wood pellet line for mixed hardwood and softwood sees that same feed one week and slab ends the next, which is why the chipper stays in the list.

A ring die sawdust pellet mill fed the same material sees fine dry fibre all year, which is the easiest feed a press can be given. The chipper is bought for the days when logs and slab ends arrive, and a line that never sees a log does not need it.

Raw material mix for a wood and MDF pellet production line including sawdust, chips, shavings and board offcuts
Why Does an MDF Pellet Production Line Need Drying?

Because MDF dust arrives dry but the board it came from does not, and a press fed at the wrong moisture makes a pellet that crumbles in the bag.

MDF is a resin-bonded board, and its density sits well above natural softwood, which changes three things on the line. The crusher draws more power per tonne because the material resists impact. The die wears faster because the resin and the mineral fillers in the board are abrasive. The press needs a steadier feed because the dust is fine enough to flush through the die rather than be compressed in it.

Table 3: Why an MDF pellet production line is not a wood line with a different feedstock name. The resin does the work that lignin does in natural wood, and it also wears the tooling.
PropertyNatural SoftwoodMDF Board
DensityLower, varies by speciesHigher and consistent
StructureFibre with natural ligninFibre bonded with resin
Effect on the dieNormal wearFaster wear, shorter die life

An MDF pellet holds together without added binder for the same reason a wood pellet does. The heat and pressure in the die soften the binder already in the material, and the pellet knits as it cools. What MDF changes is not the need for a binder but the rate at which the die is consumed.

An MDF dust pellet machine therefore runs a shorter die life than the same press on softwood, and the store level follows the board content of the mix rather than the tonnage.

Wood fuel pellet making line with dryer and ring die press handling MDF and wood dust
Which Machine Cuts Logs for a Wood Pellet Line?

The drum chipper first, then the hammer crusher, because the dryer only accepts material between 2 mm and 20 mm.

The chipper takes logs up to 18 cm and reduces them to chips, and the crusher takes those chips down to the 2-20 mm band the duct dryer is built for. Put a 30 cm log in front of the chipper and it stalls; put a 40 mm chip into the duct and it drops out of the airstream at the first bend and sits there.

Table 4: Particle size through the line. The dryer inlet band is why the crusher sits between the chipper and the duct.
StageInlet SizeOutlet Size
Drum chipperLogs under 18 cmChips
Hammer crusherChips and offcuts2-20 mm
Air duct dryer2-20 mm at 10-80 percent moisture2-20 mm at 15 percent
Ring die biomass pellet making machineFine material at 12-15 percent4-12 mm pellets

The order is fixed for a second reason. A duct carries its load in suspension, so a particle that is too big or too heavy drops out at the first bend and stays there. Crushing before drying is what keeps the material airborne, and it also keeps the wear parts out of the hot zone.

Drum chipper and hammer crusher reducing logs and offcuts to the 2-20 mm band required by the duct dryer
How Does the Duct Set the Wood Pellet Line Rate?

At 1.2-1.5 t/h the duct matches the press and leaves nothing in reserve, so a wetter feedstock slows the whole line.

Table 5: The four-bend air duct dryer as quoted for this line.
Dryer ItemSpecification
Model400, four bends
Duct length17 m
Duct section1.5 x 3.5 m
Fan power7.5 kW
Inlet moisture10-80 percent
Outlet moisture15 percent
Capacity1.2-1.5 t/h

A wood pellet line with dryer at this size holds 1.2-1.5 t/h through the duct, which is why the duct and the press are matched rather than the duct being oversized. The 10-80 percent inlet range is the figure that matters commercially. A line fed sawdust at 15 percent barely uses the duct; the same line fed wet chips at 50 percent runs the fan at its limit and the press waits. The 1.5 t/h pellet figure assumes dry-ish feed going into the duct.

A duct dries in seconds rather than minutes, and the bends are what buy that time. Each turn throws the particle across the hot gas stream and back into it, so the four-bend duct at 17 m puts the material through the hot zone four times where a two-bend duct gives it two. A wetter feedstock calls for more bends rather than a bigger fan.

Table 6: The three air duct sizes. The four-bend unit is the one that holds 1.5 t/h on this line, and the two-bend unit serves a line running on dry sawdust.
ModelBendsDuct LengthDuct SectionFan Power
219Two bends7.5 m1.5 x 3 m4 kW
325Three bends13 m1.5 x 3.5 m7.5 kW
400Four bends17 m1.5 x 3.5 m7.5 kW

A biomass pellet line with a hot air dryer also needs the heat source named before the line is ordered. The duct takes hot gas from a furnace, and the furnace is a separate item, sized on the water that has to be evaporated rather than on the tonnage. The fan in the drying row moves that gas; it does not make the heat.

Pipe wood dust sawdust dryer machine with four-bend air duct and 7.5 kW fan
What Are the Key Features of the Ring Die Wood Biomass Pellet Mill?

Six features carry this press at 1.5 t/h: a vertical ring, rollers running inside it, a compression ratio that sets density, hoist access for the die, automatic lubrication, and a wear surface built for abrasive material. A ring die wood pellet machine holds that rate because the die geometry does the work all shift, not because the motor is large.

Table 7: The ring die features that matter on a wood line. On a flat die the load lands on one patch of a plate, which is why flat dies stop at about 500 kg/h.
FeatureWhat It DoesWhy It Matters at 1.5 t/h
Vertical ring dieMaterial pressed outward through the ringLoad spreads around the full circumference, so the die wears evenly
Rollers inside the ringTwo or three rollers sweep the die faceA steady 1.5 t/h without a worn patch on one side
Compression ratioHole length against hole diameter sets densityPellet hardness is a die choice, not a motor choice
Hoist access to the dieRing lifts out with the roller assemblyA die change is 2-4 hours rather than a full day
Automatic lubricationGreases rollers, main shaft, gearbox and bearingsNo daily greasing round on a two-shift line
Wear-resistant die surfaceHolds the hole profile under abrasionMDF and hardwood shorten die life, not pellet quality
Ring die wood pellet mill with vertical ring, rollers inside the die and automatic lubrication system
Close view of the ring die and roller assembly on the MKLH560 wood pellet press

The ring geometry is what allows the press to hold 1.5 t/h all shift. Material is thrown outward against the whole circumference and the rollers sweep the full face, so no single area of the die does more work than the rest.

Table 8: The ring die range. A 1.5 t/h requirement sits at the top of the 560 row and the bottom of the 560A row.
ModelMain MotorCapacityPellet DiameterWeight
MKLH56090 kW1-1.5 t/h4-12 mm5.2 t
MKLH560A132 kW1.5-2 t/h4-12 mm5.6 t
MKLH700160 kW2-2.5 t/h4-12 mm7.2 t
MKLH860A250 kW3-4 t/h4-12 mm9.5 t

A 1 ton per hour wood pellet line and a 1.5 t/h line differ by the press and by nothing else in the machine list. The ring die wood stove pellet making machine is the machine that decides the pellet density.

A ring die wood pelletize machine holds that density because the die geometry does the work every hour of the shift, not because the motor is large. Density comes from the compression ratio of the die, which is the length of the hole against its diameter, and not from the motor size. A longer hole makes a denser pellet and draws more power; a shorter hole makes a softer pellet at the same tonnage.

Rollers run inside the ring and press outward, so the load is spread around the full circumference and the die wears evenly. The same frame is sold as a ring die biomass pellet machine for straw and agricultural waste, with a die cut for that material.

A ring die biomass fuel pellet making machine for straw needs a longer compression ratio than wood, and the same press accepts both dies. That is what allows a single press to hold 1.5 t/h for a shift without the die developing a worn patch on one side.

Ring die wood stove pellet machine MKLH560 with 90 kW main motor
Ring die wood pellet processing equipment showing die, rollers and feeder on the production line
What Power Does a Complete Wood Pellet Production Line Draw?

230.85 kW connected, and the press is 90 kW of it.

Table 9: Connected load of the complete line. The furnace fan and the site lighting are not in this figure.
StagePower
Drum chipper63.5 kW
Hammer crusher with fan52.5 kW
Screw conveyors, two units3.0 kW
Air duct dryer, fan7.5 kW
Buffer bin feeder2.2 kW
Ring die press90.0 kW
Belt conveyors, two units4.4 kW
Cooler and screener4.75 kW
Bagging machine3.0 kW
Connected total230.85 kW

Two motors dominate the starting case: the 90 kW press and the 55 kW chipper motor inside the 63.5 kW chipper block. Neither starts against a load, but both draw several times running current for the first seconds, so the incoming supply is sized on the larger of the two starts rather than on the 230.85 kW running total.

The furnace is not in the 230.85 kW. Heat comes from combustion, and the electrical load of a furnace is its fan and its controls, which are quoted with the furnace rather than with the line.

How Is a Wood Pellet Production Line Laid Out?

One row about 38 m long and 8 m wide, with the duct and the press on the same level and the buffer bin between them.

Table 10: A working layout for a 1-1.5 t/h line. The 18 m drying zone is set by the 17 m straight duct.
ZoneLengthWhat Sits There
Log deck and chipper8 mLog storage, chipper, discharge conveyor
Crushing4 mCrusher, cyclone, dust bags
Drying18 mDuct, furnace connection, fan
Pressing4 mBuffer bin, press, die access
Cooling and bagging4 mCooler screener, bagging head, bag stack

The press needs clear space on both sides of the die because a die change is a lifting job. A wood pellet production line layout is fixed by the dryer length first and the press access second, because those are the two items that cannot be moved once the building is up. A ring die on this size of press is removed with a hoist, and a line laid out with the press against a wall turns a two-hour job into a full day.

The duct is the other item that needs room. It is 17 m of straight pipe in a 3.5 m high section, and it cannot be folded around a corner to save floor, so the drying zone is the one place where a shorter building shows up as a slower line.

Which Pellet Diameter Suits Which Wood Stove?

4 mm to 12 mm, and the burner decides the size rather than the press. A domestic stove takes 6 mm, a small boiler takes 6 or 8 mm, and an industrial furnace takes 8 to 12 mm.

Table 11: Pellet diameter against application. The die sets the diameter and the press does not need to change.
ApplicationDiameterWhy That Size
Small room stove4-5 mmShort flame, fast heat release
Domestic stove and stove insert6 mmThe common European stove size, feeds through a small auger
Small and medium boiler6-8 mmBalances burn time against feed reliability
Industrial furnace8-12 mmLonger residence time on a grate
Bedding and absorbent use6-8 mmLow dust, high absorbency

A complete wood pellet production line is normally quoted with one die fitted and a second on the shelf, because a die change costs a shift. A line serving both a stove market at 6 mm and a boiler market at 8 mm keeps both sizes and runs them in campaigns.

How Long Do Pellets Need to Cool Before Bagging?

Six to fifteen minutes in the counter flow cooler, and a pellet bagged hot will sweat inside the sack.

Pellets leave the die at 70 to 90 deg C and they are soft at that temperature. A pellet dropped straight into a bag deforms under its own weight, and the moisture that flashes off inside the sack condenses on the film and turns the surface mouldy within days.

Table 12: The cooler